Audi A6 Quattro (C6) KW V2 Comfort Kit [18010059]

Purchase KW V2 Comfort Kit | 05-11 A6 Quattro

SKU: 18010059
KW V2 Comfort Kit | 05-11 A6 Quattro
Power gain Up To
+0 HP

Torque gain Up To
+0 TQ

Advertised gains are estimates of HP and Torque “at the engine” calculated from gains as measured on a Dynojet Dynamometer in ideal conditions and typically show the largest possible change. Actual gains are dependent on the following: Learn More about Crank HP Vs Wheel HP

Model – Manufacturers use the same engine in multiple model vehicles and often times they are in a different state of tune, for example: 2008 C63 and a 2008 CLK Black Series. Both have the same engine, but the C63 has 451hp while the CLK63 has 500hp. Naturally the C63 will show more gains as it starts at a lower level.

Model Year – Similar to above, as time progresses, Manufacturers tend to slightly increase power output via software from one year to the next or offer “Performance Packages” with increased power. The engines remain largely unaltered and as a result, final tuned output remains the same, while the gains are lower as the starting point is now higher.

Fuel – Fuel quality is HIGHLY important with performance vehicles. Low quality and/or low octane fuel will greatly impact engine output and potentially even engine health. Top tier brand premium fuels should always be used to achieve the best results possible.

Drivetrain – All wheel drive has higher drivetrain losses than rear wheel drive. This results in lower numbers when testing on a chassis dyno. Wheel/tire size and weight will also impact chassis dyno results

Weather/Conditions – Temperature, humidity, altitude, and air density all impact engine performance. Heat, high humidity, and thin air will all work towards reducing engine output

Engine Health – Higher miles tends to result in increased build up and lower compression which can and will impact engine output. Properly maintained engines will have better performance than abused or neglected engines.

Supporting modifications – The highest power levels require supporting modifications. Depending on the engine, this could mean forged internals, built transmission, upgraded fuel system, 110+ octane race fuel, etc.
Please confirm:
NOT LEGAL FOR SALE OR USE ON POLLUTION CONTROLLED MOTOR VEHICLES
Learn why

Confirmation
Please confirm that you are not installing this product within the United States.

This policy only applies to installers and/or users who are in the United States, customers who reside in other countries should act in accordance with their local laws and regulations.

Some Weistec Engineering performance upgrades may solely be used on vehicles in sanctioned competition which may never be used upon a public road or highway, unless permitted by specific regulatory exemptions (such as a CARB E.O.). For state specific details please visit the following website. http://www.semasan.com/emissions

It is the responsibility of the installer and/or user of the product to ensure that it is used in compliance with all applicable laws and regulations. If a product was purchased in error, do not install and/or use it. The purchaser must arrange to return the product(s) for a full refund.

All performance modifications and installations are at the customer’s own risk. Weistec Engineering holds no responsibility either implied or otherwise for mechanical, electrical or other failure when using any aftermarket performance products.
$2,459.00 $2,459.00
QTY:
Install instructions
Prop 65 warning

Warning
This product can expose you to chemicals including carbon black, silica - crystalline, formaldehyde, and lead which are known to the State of California to cause cancer, and lead, which is known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

Product details

Manufacturer	KW Suspensions
UPC	842607064449

Vehicle application

year	make	model	trim	engine
2011	Audi	A6 Quattro	Base (C6)	3.2L V6 (BKH)
2010	Audi	A6 Quattro	Base (C6)	3.2L V6 (BKH)
2009	Audi	A6 Quattro	Base (C6)	3.2L V6 (BKH)
2008	Audi	A6 Quattro	Base (C6)	3.2L V6 (BKH)
2007	Audi	A6 Quattro	Base (C6)	3.2L V6 (BKH)
2006	Audi	A6 Quattro	Base (C6)	3.2L V6 (BKH)
2005	Audi	A6 Quattro	Base (C6)	3.2L V6 (BKH)
See more

Instructions

Install instructions

Product Description

Built with paramount attention to detail and using only the highest quality components, the stainless-steel KW V2 Comfort coilover struts are 100 percent corrosion-resistant and have an unlimited lifespan. The dirt resistant trapezoid shaped threads and the adjustable composite spring seat mean that the ability to adjust the ride height of the vehicle will not be affected even after many years of driving allowing you to emphasize the sportiness of your vehicle visually.

Application Guide

2005-2011 Audi A6 (C6/4F) Sedan; 2WD + Quattro 4WD; all engines

Key Features and Benefits

KW suspensions V2 Comfort coilovers are hand built by our expert team and each given a uniquely individual serial number at our headquarters in Fichtenberg, Germany.
Every KW damper is dyno tested to ensure accuracy and preset to our recommended shock settings before being released for delivery.
Adjustable rebound damping allows you to influence the ride characteristics. Paired with vehicle specific spring rates precisely tuned by our engineers, V2 Comfort coilovers allow you to dial in the level of comfort you prefer.
TVR-A (Twin Valve Rebound - Adjustable) technology - allows oil to flow passed an adjustable, conical low-speed bypass during slow damper speeds, while at higher speed, the main rebound stage valve opens for maximum fluid displacement.
Composite spring perch made from wear-resistant, friction-optimized polyamide composite encompassing a stainless-steel insert. The polyamide composite prevents oxidation while the stainless-steel insert maximizes strength.
Inox-Line Stainless Steel - Truly Permanent Corrosion Resistance. Inox-Line coatings will not wear off while adjusting the suspension making KW coilover struts 100 percent corrosion resistant with an unlimited lifespan.
Seamless Ride Height Adjustment - the corrosion resistance of the Inox-line stainless steel and composite perches means easy ride height adjustability to help you dial in your preferred look.
Elastomer Bump stop with integrated dust protection system prevents water and dirt particles reaching the piston rod and seals. The highly resilient bump stops act as dynamic load limiters while maintaining ride quality and durability

Product Documents

Notes

10: For V2, V3 & Street Comfort coilovers, front shock absorbers need to be removed from the car for adjustment of stiffness
2: Height adjustable front and rear axles (front axle threaded strut housings, rear axle adjustable springs + dampers)
62: Not for vehicles with electronic damping
69: Coilover strut housing in galvanized steel construction.

Lower Rates

Front: 0.8-1.6"
Rear: 0.8-1.6"

KW V2 Comfort Kit | 05-11 A6 Quattro

Power gain Up To

Torque gain Up To